ZHCSBL4A September   2013  – January 2015

PRODUCTION DATA.  

1. 1 特性
2. 2 應用
3. 3 說明
4. 4 修訂歷史記錄
5. 5 說明（續）
6. 6 Pin Configuration and Functions
7. 7 Specifications
   1. 7.1 Absolute Maximum Ratings
   2. 7.2 ESD Ratings
   3. 7.3 Recommended Operating Conditions
   4. 7.4 Thermal Information
   5. 7.5 Electrical Characteristics
   6. 7.6 Timing Requirements
   7. 7.7 Typical Characteristics
8. 8 Detailed Description
   1. 8.1 Overview
   2. 8.2 Functional Block Diagram
   3. 8.3 Feature Description
      1. 8.3.1 Device Power Up
         1. 8.3.1.1 Power-On-Reset (POR)
         2. 8.3.1.2 Power Up from Battery without DC Source
            1. 8.3.1.2.1 BATFET Turn Off
            2. 8.3.1.2.2 Shipping Mode
         3. 8.3.1.3 Boost Mode Operation from Battery
            1. 8.3.1.3.1 Integrated Control to Switch Between USB Charge Mode and Boost Mode
         4. 8.3.1.4 Power Up from DC Source
            1. 8.3.1.4.1 REGN LDO
            2. 8.3.1.4.2 Input Source Qualification
            3. 8.3.1.4.3 Input Current Limit Detection
            4. 8.3.1.4.4 D+/D- Detection Sets Input Current Limit
            5. 8.3.1.4.5 Force Input Current Limit Detection
         5. 8.3.1.5 Converter Power-Up
         6. 8.3.1.6 Low Power HIZ State
      2. 8.3.2 Power Path Management
         1. 8.3.2.1 Narrow VDC Architecture
         2. 8.3.2.2 Dynamic Power Management
         3. 8.3.2.3 Supplement Mode
      3. 8.3.3 Battery Charging Management
         1. 8.3.3.1 Autonomous Charging Cycle
         2. 8.3.3.2 Battery Charging Profile
         3. 8.3.3.3 Thermistor Qualification
            1. 8.3.3.3.1 Cold/Hot Temperature Window
         4. 8.3.3.4 Charging Termination
            1. 8.3.3.4.1 Termination When REG02[0] = 1
         5. 8.3.3.5 Charging Safety Timer
            1. 8.3.3.5.1 Safety Timer Configuration Change
      4. 8.3.4 Status Outputs (STAT, and INT)
         1. 8.3.4.1 Charging Status Indicator (STAT)
         2. 8.3.4.2 Interrupt to Host (INT)
      5. 8.3.5 Protections
         1. 8.3.5.1 Input Current Limit on ILIM
         2. 8.3.5.2 Thermal Regulation and Thermal Shutdown
         3. 8.3.5.3 Voltage and Current Monitoring in Buck Mode
            1. 8.3.5.3.1 Input Over-Voltage (ACOV)
            2. 8.3.5.3.2 System Over-Voltage Protection (SYSOVP)
         4. 8.3.5.4 Current Monitoring in Boost Mode
         5. 8.3.5.5 Battery Protection
            1. 8.3.5.5.1 Battery Over-Voltage Protection (BATOVP)
            2. 8.3.5.5.2 Battery Short Protection
            3. 8.3.5.5.3 System Over-Current Protection
   4. 8.4 Device Functional Modes
      1. 8.4.1 Host Mode and Default Mode
   5. 8.5 Programming
      1. 8.5.1 Serial Interface
         1. 8.5.1.1 Data Validity
         2. 8.5.1.2 START and STOP Conditions
         3. 8.5.1.3 Byte Format
         4. 8.5.1.4 Acknowledge (ACK) and Not Acknowledge (NACK)
         5. 8.5.1.5 Slave Address and Data Direction Bit
            1. 8.5.1.5.1 Single Read and Write
            2. 8.5.1.5.2 Multi-Read and Multi-Write
   6. 8.6 Register Map
      1. 8.6.1 I2C Registers
         1. 8.6.1.1  Input Source Control Register REG00 [reset = 01011000, or 58]
         2. 8.6.1.2  Power-On Configuration Register REG01 [reset = 00011011, or 0x1B]
         3. 8.6.1.3  Charge Current Control Register REG02 [reset = 00100000, or 0x20]
         4. 8.6.1.4  Pre-Charge/Termination Current Control Register REG03 [reset = 00010001, or 0x11]
         5. 8.6.1.5  Charge Voltage Control Register REG04 [reset = 10110010, or 0xB2]
         6. 8.6.1.6  Charge Termination/Timer Control Register REG05 [reset = 10011100, or 0x9C]
         7. 8.6.1.7  Boost Voltage/Thermal Regulation Control Register REG06 [reset = 10010011, or 0x93]
         8. 8.6.1.8  Misc Operation Control Register REG07 [reset = 01001011, or 4B]
         9. 8.6.1.9  System Status Register REG08
         10. 8.6.1.10 New Fault Register REG09
         11. 8.6.1.11 Vender / Part / Revision Status Register REG0A
9. 9 Application and Implementation
   1. 9.1 Application Information
   2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
         1. 9.2.2.1 Inductor Selection
         2. 9.2.2.2 Input Capacitor
         3. 9.2.2.3 Output Capacitor
      3. 9.2.3 Application Performance Plots
10. 10Power Supply Recommendations
11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
12. 12器件和文檔支持
    1. 12.1 文檔支持
       1. 12.1.1 相關文檔　
    2. 12.2 商標
    3. 12.3 靜電放電警告
    4. 12.4 術語表
13. 13機械封裝和可訂購信息